Windows 2003 SBS Transition Pack Upgrade

Man, where do I start with this…

Had to transition a client that had fully outgrown their SBS server. To cut a long story short, its not that they hit the 75 user limit. It’s because they wanted to introduce extra complexity that an SBS system couldn’t handle. Ie. Multiple secondary servers, file replication, etc.

Just to make other people’s lives easier, here’s the order  in which the transition needs to be performed:

Windows 2003 SBS Premium (non R2)
1. Upgrade to 2003 SBS Premium R2
2. Apply SBS 2003 Transition Pack
3. Test and Deploy server applications to other servers
4. Purchase kit

1. Upgrade to 2003 Premium R2

Before attempting the Upgrade to R2, make sure you only have SP1 installed on the SBS server. It’ll make you’re life a lot easier. If it’s been patched to SP2, remove it. Also, make sure that SP1 for SBS has been applied “properly”. If you’re picking up a site from an IT admin that has no idea, then double check. SBS SP1 contains 5 patches that need to be applied. Obtain from here:

http://www.microsoft.com/downloads/details.aspx?FamilyId=B6F8A4C0-B707-4161-ADEB-44F1B756119F&displaylang=en

If SBS SP1 has not been applied properly, then you’ll probably get all sorts of errors saying SBS is not the right SP level.

Once you’ve sorted this out, run the SBS R2 upgrade.

2. Apply SBS 2003 Transition Pack

Now, from the yellow slip in the box, it appears you can transition directly from R1 SBS (and you don’t need to transition from R2 SBS). But in my case, my licensing contact said I had to transition from R2 SBS so I followed his advice. In the end, the bulk of the cost is with the Transition pack anyway, the R2 upgrade is outweighed.

Installing the Transition pack involves inserting the CD and following the wizard. It does the rest. After a few reboots, everything should complete. I had an issue however with the second phase of the transition. I received the following message:

Report System CompatabilityThe following items are not compatible with windows.

The compatability issue with some of these items must be resolved before running setup again.

X Small Business Server 4.0

! Service packs and/or quicm fix (QFE) updates

! Port configuration for Routing ans RemoteAccess Service

! Windows 95 and Windows NT 4.0 interoperability issues (Read Details)

The upgrade then bombed out, restarted the server and said it was complete. Same error as here:
 http://www.eggheadcafe.com/forumarchives/windowsserversbs/Aug2005/post23994025.asp

Nonetheless, everything looks ok. All the SBS branding has been converted to Standard. This last part that bombed out appears to only update the OS and it’s files. The SBS transition happens in the steps prior.

To prevent this from happening to you, and for a successful transition, I can only suggest you try this:
http://blogs.technet.com/sbs/archive/2006/01/12/417350.aspx

And finally, here we go to the GOTCHAS!This is truly what the post is aimed towards - this is what people call PSS for.

6-Before installing the transition pack make sure you Export and Remove the following

registry key:HKEY_LOCAL_MACHINESOFTWAREMicrosftSmall Business

Note: There will be a SMALLBUSINESSSERVER key and that is OK, we are only interested

in the “Small Business” key. Presence of this registry key when installing the

Transition pack may cause it to fail.

Hope this helps with anyone else attempting this transition.

3. Test and Deploy server applications to other servers

Test to make sure your SBS server is no longer SBS. You should see that the licensing logging service has now been disabled. Also, I performed an ADPREP and introduced a secondary domain controller. Seems to have worked well. This is something you would not be able to do if the SBS restrictions were still in place.

You can now install your applications on other servers. For me, the aim was to get SQL 2005 onto a seperate server. I can offer a tip here. Attempt to install SQL 2005 onto the SBS box first so you can obtain the serial number. The serial is autofilled, so you won’t find it written anywhere. With the serial, you can then install it onto a seperate server. Please keep in mind that if you have not transitioned SBS, you are not entitled to do this. Furthermore, when you transition SBS you need to buy seperate SQL CALs as the transition pack only covers Exchange!

4. Purchase Kit

This is what I purchase to complete my upgrade (this covers SBS R1 Premium to SBS R2 Premium, and covers the one install of Windows 2003, Exchange and SQL only):

Upg SBS to R2 -> MS WIN SBS PRM 03 R2 VUP CD/DVD

Transition Pack -> MS WIN SBS PRM 03 R2 5 CLT TRANS

CAL Transfer -> MS WIN SBS CAL 2003 5 TRANSTN PAK

SQL Licences -> Microsoft SQL Workgroup CAL 2008 Sngl OPEN No Level User CAL

Last word

Not such a bad experience in the end considering the amount of time it could’ve taken without the transition pack. What I should also mention is that although I had SBS R2 to begin with, after the transition it’s just 2003 Standard R1. I looked this up online, and the consensus is that SBS R2 is not actually Windows Server 2003 R2.

HTC Touch Diamond LCD and Digitizer replacement Guide (HOW TO)

Before you proceed, please note that I cannot be accountable/liable for any damage caused to your phone. This is only a guide! 

I will mention that I am only going through the steps once you have disassembled the phone according to the various guides available on the Internet.Namely, the official HTC service manual or this Russian site here:http://www.pdacenter.ru/razborka/razbor-htc-touch-diamond/

There are plenty of guides on the net on how to disassemble the HTC Diamond, but little about replacing the LCD/Digitizer (hence my write up here!). 

I apologise that I have not taken pictures at every stage of this process, but I will attempt to explain everything in as much detail as possible. Some pictures I have managed to take are a little blurry, but hopefully you get the drift. 

Getting Started

Once you have managed to dismantle the phone to this point, please follow on with this article. At this point, the screen is still glued to the chassis (very tightly!).

1. Dismantle to basic chassis

To proceed, you will need to pry off the screen. People have recommended using credit cards, which will do the trick nicely once you have managed to find an opening to leverage from. Hopefully, if you have bought your replacement tool they have given you some sort of plastic tool to lever with. The tool on the left works best.

Tools needed

At this point, you will pretty much have to use the lever and a credit card to pry the glue loose. If done successfully, you will have something that looks like this.

Seperated parts

Now at this point, you could try and separate the LCD from the digitizer if you only bought one or the other. I suggest that you replace both the LCD and digitizer as there is a high chance that you will not be able to separate them without breaking one or the other. This is just my opinion but there have been people who have successfully done this. If you manage to separate them both, you’ll need to desolder the connection between the LCD and digitizer (4 contact points on a ribbon cable – can be seen on the left in the image below).

The image below shows the silver foil and plastic insulation removed from the rear of the LCD/digitizer unit. Remember the order in which you peeled off the insulating tape and the silver foil! I will explain the problem I had a little later.

Back of LCD

For me, I bought a new LCD and digitizer separately, so I had to solder the 4 contacts on the left myself (notice the arrow). This wasn’t too hard to do if you have ever soldered stuff before. Just make sure there is no shorts between the contacts. To avoid this work, you should buy the LCD/digitizer preassembled as one unit.Once you have put together the LCD and digitizer, you will need to remove any of the scratch protective plastic layers off them. Put them together as they’re suppose to be and then stick them back into the chassis. You will need some sort of glue to make the digitizer stick to the chassis. When I pulled mine apart, a lot of the glue stayed on the chassis so I simply popped the digitizer back in and pressed firmly to make it stick. This is not recommended though, as a drop of the phone will cause the digitizer to fall out!Assuming you have figured out some way to make the digitizer stick to the chassis, you’ll notice that the LCD screen also needs to be stuck to the digitizer in some manner. The way I achieved this was to tape the LCD to the chassis with thin strips of electric tape. This stopped the LCD from moving around. 

Putting it all back together

You will need make all the ribbon stick to the back of the LCD for tidyness (as above). To do so, I peeled off the double-sided tape from my faulty unit and re-used it.

When putting the silver shielding tape back on, please remember that it is conductive and can cause shorts. I spent ages wondering why my digitizer wouldn’t work and finally realised I forgot to put the yellow insulating tape back on before I put the silver shielding tape back over the ribbon with the 4 contacts that I had to solder (see picture below)!

Start assembling

When you are putting it back together, there is a point where there are 2 sets of ribbon cable that need to make contact with a floating circuit board that sits on top. These two contacts need to be secured properly, and the best way to do it is to view it from side on and use a thin flat head screw driver to firmly press in those contacts. The image below shows the side on view I’m talking about.

Assembly side on view

The two parts I am referring to are these:

The two parts

When putting it back together, follow the service manuals or just remember what you pulled apart.

I suggest that before you put everything back together entirely, that you slip the battery in and give it a quick test at this point.

Quick test at this point

With any luck, the phone turns on, the LCD screen lights up, and the digitizer works! I hope this article helps some people out there who are wondering how to change that screen.

All done!